Home > Hewlett Packard > Hewlett Packard Hp Nbsp Driver

Hewlett Packard Hp Nbsp Driver

I have got: > > usb-ohci 18880 0 (unused) > (...) > usbcore 47744 1 [printer usb-ohci] > > in the listing on /sbin/lsmod. Maybe this > will go away when > everything is fixed. What does this mean? And the good news is that one exists. check my blog

Make is executable, same attributes as lpd has. If ptal-init recognise your printer, then ptal-init start /etc/init.d/lpd start configure it with yast2, change the /etc/printcap file as it is described in the manual. Put the printer module just before, like: ... Unfortunately, this can be misleading because it only applies if the tape drive and the picker are connected to the same SCSI card.

Helped me and/or pointed me to the information. Pavia n° 145087 | Reg. OK, as new to this list, I had to look in the archive to see the previous posting, I see you use SuSE 7.3 which triggered me.

with ? sit on /dev/usb/lp0 for a minute or more), ra= ther > than timing out after about 15 seconds? Wolfi ============================================= mailto:[email protected] ptal-hp: error opening PML for device "mlc:usb:PSC_750xi"!

Jan 20 13:39:58 linux ptal-mlcd: ERROR at ExMgr.cpp:2332, dev=, pid=1474, errno=19 Couldn't find device! Wolfi =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D mailto:[email protected] _________________________________________________________ Do You Yahoo!? Jan 20 13:39:01 linux ptal-mlcd: SYSLOG at ExMgr.cpp:660, dev=, pid=1412, errno=111 ptal-mlcd successfully initialized. Intel and VIA chipsets are generally UHCI, and others are generally OHCI.

There is absolutely no warranty for GDB. Could i use it in any way ? Loaded symbols for /usr/lib/libstdc++-libc6.2-2.so.3 Reading symbols from /lib/libm.so.6...(no debugging symbols found)...done. Use no rewind, Berkeley.

Yes, I think many will find the information there useful. http://biffignandigroup.com/kusg/PVD Thanks. Please give me the output of running the "bt" command. Please give me the output of running the "bt" command.

Run "ps auxwww|grep [p]tal-mlcd" to find the process ID of > > > ptal-mlcd. click site mc -p /dev/picker -r DS - Report full/empty status of drives & slots. I can't figure out what the various error messages mean, e.g. Could i use it in any way ? > What has been planned about it ? > thanx in advance, zbyszek Hi, Zbyszek.

Should I edit my > etc/modules.conf as well? Enterprise LAN Specialist Information Technology Services Division Ministry of Attorney General "Fisher, Ron A" wrote: > It once again goes to show that HP Laserjet OEM drivers are a big joke Here it goes: gdb /usr/sbin/ptal-mlcd 362 GNU gdb 5.1 Copyright 2001 Free Software Foundation, Inc. news I have got: > > usb-ohci 18880 0 (unused) > (...) > usbcore 47744 1 [printer usb-ohci] > > in the listing on /sbin/lsmod.

The PSC 750 is indeed supported by version 0.8, as it falls under the "PSC 700 series" entry on the Supported Devices page at http://hpoj.sf.net/suplist.shtml. Go back to the configuration steps and make the device file. -------------------------------------------------------------------------------- Test It -------------------------------------------------------------------------------- If these tests fail, recheck the configuration. This will be done by /sbin/rc0.d/K890kmbuild at shutdown or by /sbin/rc1.d/S110kmbuild upon bootup. 7.

The next most common problem is using the wrong driver. -------------------------------------------------------------------------------- Outline of steps -------------------------------------------------------------------------------- - You might have to add the right driver to the kernel (spt or sctl). -

System: AMD 1700+/512MB Distro: Mandrake 8.1 Printer: HP PSC750 hpijs 1.0 After David's last message, I changed the /etc/modules.conf "usb-uhci" to "uhci" then rebooted. Yes it hangs forever. > > Although you might reasonably assume that your USB hardware is OK becau= se > it works under Windows, please try removing as many USB devices Search for a line that contains at the moment the usb-ohci. Sign up for the SourceForge newsletter: Country Afghanistan Aland Islands Albania Algeria American Samoa Andorra Angola Anguilla Antarctica Antigua and Barbuda Argentina Armenia Aruba Australia Austria Azerbaijan Bahamas Bahrain Bangladesh Barbados

Is it better now? That=B4s all. Alternatively, do you know if your 2.4.16 kerne= l is > the "standard" unpatched version, or does it contain Debian-specific > patches? More about the author Jan 20 13:39:01 linux ptal-mlcd: ERROR at ExMgr.cpp:2332, dev=, pid=1386, errno=19 Couldn't find device!

cc scsi_io.c - Compile the test program. ./a.out /dev/picker - Run the test program. Z7_3054ICK0K8UDA0AQC11TA93082 hp-hero-support-search Actions ${title} Loading... I have got: usb-ohci 18880 0 (unused) (...) usbcore 47744 1 [printer usb-ohci] in the listing on /sbin/lsmod. Hi, Pablo.

Would you please try the following test for me? It appears that ptal-devid and ptal-hp are unable to find the PSC 750. bc ! Jan 20 13:39:40 linux ptal-mlcd: SYSLOG at ExMgr.cpp:660, dev=, pid=1435, errno=111 ptal-mlcd successfully initialized.

usb]# ptal-devid /dev/usb/lp0
ptalDeviceOpen(dev=/dev/usb/lp0) failed!

looked up "class/subclass/protocol" in usbview & got

PSC 750xi
Manufacturer: Hewlett-Packard
Serial Number: MY16LB11VKWB
Speed: 12Mb/s (full)
USB Version:  1.10
Device Class: 00(>ifc )
Device Subclass: Probing "/dev/usb/lp1"... Jan 20 13:39:59 linux PAM-unix2[1336]: session finished for user root, service su Jan 20 13:41:06 linux automount[657]: attempting to mount entry /misc/.directory Jan 20 13:41:06 linux automount[1488]: lookup(file): lookup for .directory with ?

This time, don't forget to issue the "bt" > (backtrace) command that I requested. :-) > > David Ooops, sorry David, I was in a hurry this morning.