Home > Hauppauge Wintv > Hauppauge Wintv Nova-td Linux Driver

Hauppauge Wintv Nova-td Linux Driver

Contents

With 12.10/0.25 my MythTV log was full of auto bandwidth >not being a valid setting, so I changed to using 8MHz bandwidth and can now >occasionally get a lock, but mostly NOTE: For see if your PC recognize and configure correctly the WinTV-NOVA-T-Stick use this command (from the terminal): dmseg now find a line like this: [ 175.812573] dvb-usb: Hauppauge Nova-T Stick I recently built a system for a friend of mine, using Fedora 18 x64. To avoid spurious remote control signals with 1.20 firmware, you need to edit /etc/modprobe.d/options or from Ubuntu onwards /etc/modprobe.d/options.confand add: options dvb_usb disable-rc-polling=1 November 28,2008 - i2c errors. this contact form

DRIVER="dev/input" # If DEVICE is set to /dev/lirc and devfs is in use /dev/lirc/0 will be # automatically used instead REMOTE_DEVICE="/dev/input/by-path/pci-4-1--event-ir" MODULES="" # Default configuration files for your hardware if any I set it to that and it worked, so I never tried > smaller delays. Gary _______________________________________________ mythtv-dev mailing list [email protected] http://www.mythtv.org/mailman/listinfo/mythtv-dev Re: Problems with Hauppauge Nova TD Dual Tuner USB Stick and Mythtv, no problems in Windows! [ In reply to ] stephen_agent at jsw Apr12,2013,7:11PM Post Internal label says: WinTV-NOVA-TD-500 DVB-T 84109 LF REV E1F4 Product of Indonesia. find more

Hauppauge Wintv Nova-t Drivers

The output of dmesg is supposed to look like that. end So each 2nd keypress will be suppressed. You're not trying to set it up as a V4L device in MythTV are you? This typically happens when using a masthead amplifier or distribution amplifier to feed multiple TVs from a single TV aerial.

You'll have adapter0 and adapter1 in /dev/dvb, which you can use separately. lrwxrwxrwx 1 root root 9 2008-02-07 20:31 pci-0000:00:1a.1-usb-0:2:1.0-event-kbd -> ../event1 lrwxrwxrwx 1 root root 9 2008-02-07 20:31 pci-0000:00:1a.1-usb-0:2:1.1-event-mouse -> ../event2 lrwxrwxrwx 1 root root 9 2008-02-07 20:31 pci-0000:00:1a.1-usb-0:2:1.1-mouse -> ../mouse1 lrwxrwxrwx My Hauppauge WinTV Nova TD-500 > >> PCI dual tuner card has one that turns on the low noise amplifier. Typing dmesg | grep dvb [ 12.879450] dvb-usb: found a 'Hauppauge Nova-TD Stick/Elgato Eye-TV Diversity' in warm state. [ 12.879597] dvb-usb: will pass the complete MPEG2 transport stream to the software

For convert the mt2 format to DVD format follow the explanation below. Nova Td Paintball My memory fades, but I think the magic fix in the past was setting the bandwidth to auto. Die folgenden Schlagworte wurden dem Artikel zugewiesen: Multimedia, TV, Hardware, ungetestet Wiki Hauppauge WinTV Nova-T Stick Powered by Inyoka Inyoka v0.15.8 Zur mobilen Version 2004 – 2017 ubuntuusers.de • Einige Rechte Unfortunately, some keys may generate keycodes that X doesn't recognize at all and the device does not support keymaps, or this would be easy to fix.

The above mentioned dib0700_new_12c_api.patch is not available discretely but is now rolled into the mercurial drivers dvb-usb-dib0700-1.20.fw firmware file is now stable for reception, but remote control functionality is broken; any You will need the dvb-usb-dib0700-1.20.fw firmware file in /lib/firmware or the relevant place for your distribution. Yes, my different tuners all have different sensitivity. You need to know the name of the driver - in my case, it is dvb_usb_dib0700 so the command: modinfo dvb_usb_dib0700 produces a big listing with these "parm" values at the

Nova Td Paintball

The above mentioned dib0700_new_12c_api.patch is not available discretely but is now rolled into the mercurial drivers dvb-usb-dib0700-1.20.fw firmware file is now stable for reception, but remote control functionality is broken; any http://www.emcu.it/UBUNTU/HauppaugeWinTV-NOVA-T-Stick/HauppaugeWinTV-NOVA-T-Stick.html Ideally the masthead amplifier should be turned down to a very low setting, and if necessary followed with a 6dB or 12dB (as necessary) attenuator. Hauppauge Wintv Nova-t Drivers This is believed to be a subtle hardware incompatibility, where the Hauppauge WinTV-NOVA-T-500 card prevents the motherboard's north bridge from using low power states. Mythtv As the device isn't supported properly in Myth/Linux I had to compile the V4L drivers, I'm running Fedora 18 x64 Kernel 3.8.4-202 and V4L compiled last night, using Mythtv from the

Now performing a scan I get the following: scan /home/dave/dvb-apps/util/scan/dvb-t/uk-SandyHeath scanning /home/dave/dvb-apps/util/scan/dvb-t/uk-SandyHeath using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 641833000 0 3 9 1 0 0 0 initial transponder 665833000 0 2 http://tuiconverter.com/hauppauge-wintv/hauppauge-wintv-nova-s-drivers.php The fact that some apps work doesn't mean that it's a MythTV fault, just that there are different ways of using the same API. -- Stuart Morgan MythTV _______________________________________________ mythtv-dev mailing I will point out that whether the splitter is internal or external, the losses are (approximately) equivalent. Good points and I don't disagree. Td Stock

Well actually I've been fighting my TD >>> ever >>> since I bought it, but before 12.10 I felt like I was winning. >>> >>> My memory fades, but I think Specific to the model Remote control key codes Snowboard remote control Grey top, black bottom, 45 buttons, snowboard shape. Therefore I recommend the linuxtv-dvb-apps package which you can find in the community repository. navigate here Adequate power level to the tuner is.

So either you just rename the firmware linked above or put a link. Oddly, this same procedure has also been necessary after changing X11 parameters to switch between HDMI and VGA. Contact me if you need more detailed information about my kernel ..... /Henrik On Dec 16, 2007 5:07 PM, Tomas wrote: > Hello, > > I'm having problems tuning my

About the stabilty of this driver The current drivers are close to stable at the moment (2008-01-25).

In my research I noticed a fair few people >> complaining of reception problems and susceptibility to EMI. (even >> though >> a lot of people also have no trouble). As Gary states it is difficult to get meaningful numbers from tuners for comparison - it's usually a case of trial and error and YMMV. Users may wish to continue to use 1.10 unless they have patched their v4l-dvb code with dib0700_new_i2c_api.patch. I find that a single dual tuner (with multi-rec) is perfectly adequate for us.

While most low cost devices do (and Hauppauge is a low cost device), there are alternatives (including using an internal amp) which can mitigate such issues. A new T-500 arrived today. I can make four simultaneous recordings with it whilst using a single aerial cable. http://tuiconverter.com/hauppauge-wintv/hauppauge-wintv-nova-s-pci-driver.php Diese können unabhängig von einander als adapter0 und adapter1 in /dev/dvb angesprochen werden.

My Hauppauge WinTV Nova TD-500 >> PCI dual tuner card has one that turns on the low noise amplifier. Or you can do what I had to > - use an aerial amplifier/splitter and get signal levels that are way > above the levels where problems will occur for any did you get the firmware and >> dib0700 driver? > > Hi - here was my post on linux-dvb > > Hi - I am trying to get this usb tuner of remote control: 45 buttons Snowboard Shape Silver over Black # begin remote name hauppauge-45-snowboard bits 16 eps 30 aeps 100 one 0 0 zero 0 0 pre_data_bits 16 pre_data 0x1

Sample kernel output [ 34.053116] dib0700: loaded with support for 7 different device-types [ 34.054165] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in cold state, will try to load a DRIVER="dev/input" # If DEVICE is set to /dev/lirc and devfs is in use /dev/lirc/0 will be # automatically used instead REMOTE_DEVICE="/dev/input/by-path/pci-4-1--event-ir" MODULES="" # Default configuration files for your hardware if any Note that you need to have 2 antenna leads plugged into the stick, one in the end, and the other into the side in order to get both tuners to work! This has the side-effect of disabling key repeats for the remote entirely.

you are getting nothing from device? More information about this is available on this mailing list post. To note here is that I have a VIA usb card, using my onboard nvidia USB led to hard hangs within ~4 hours with the nova-TD. Then try one of the config files below.

If you can't find a suitable initial scan file then you can build your own with w_scan (AUR). Some issues have been found with the latest version of the firmware. To solve, use the USB extension leads from the box to get the actual device away from the case and run the coaxial cable well away from the rest of your no such chip as 7700P!) Identification This device's USB ID is 2040:9580.

Relevant dmesg output: > > [ 1293.235000] usb 1-2: new high speed USB device using ehci_hcd and > address 2 > [ 1293.350000] usb 1-2: configuration #1 chosen from 1 choice If all you > need is two tuners, a dual tuner is fine. what does "lsusb" and/or "lsusb -v" reports? So if your signal levels are marginal and you need more than two tuners, dual tuners will always give a worse result than single tuners.

The mercurial drivers have been changed so they now load 1.20 firmware. devinput Settings for mapping driver output generated by your remote (a bunch of hex numbers) to key names (something like 0..9, Volume+, Next, Record) Settings for mapping key presses to actions Privacy policy About LinuxTVWiki Disclaimers Hauppauge WinTV-NOVA-T-500 From LinuxTVWiki Jump to: navigation, search WinTV-Nova-T-500 This is a dual tuner DVB-T PCI card from Hauppauge. This card has an issue (which particularly manifests itself in Australia where a bandwidth of 7MHz is used) with jittery reception - artifacts and choppy sound throughout recordings despite having full